Here is the "Electricity - Basic Navy Training Courses" (NAVPERS 10622) in its entirety. It should provide one of the Internet's best resources for people seeking a basic electricity course - complete with examples worked out. See copyright. See Table of Contents.
¶ U.S. GOVERNMENT PRINTING OFFICE; 1945 - 618779
THE UNIVERSAL MOTOR
Although there are a number of types of d-c motors, ONE, and only one, will
work on a.c. It's the so-called SERIES or UNIVERSAL motor. The term "series,"
applied to a motor means that the field and armature are connected IN SERIES with
each other. This connection is shown in figure 155. A is the wiring diagram and
B is the schematic. Since the field and armature are in series they must carry exactly
the same current. And this is the key to "why" a series-universal motor
works in a.c.
Both the armature coils and the field coils reverse current direction at the
SAME instant. They reverse together because both are carrying the same current.
The reversing current causes armature coils and field coils to change their POLARITY
simultaneously. You know that, if BOTH armature and field change polarity, rotational
direction does NOT reverse. This is proved in figure 156. A shows a motor with the
current in a positive direction (instant 1 on the graph). B shows the same motor,
but with current in a negative direction (instant 2 on the graph).
Figure 155. - Series-universal motor.
You prove that the motor has torque in the SAME DIRECTION for both directions
of current. Use the motor hand rule.
The universal motor is used on food mixers, malted milk machines, cleaners,
and some fans. It's THE motor that can be used on a.c. or d.c. Notice that the uses
of the series-universal motor all call for fractional hp motors. The motor is not
built in sizes larger than 1 hp, except for specially designed jobs.
Alternating current does certain things that direct current does not do. And
for this reason, most a-c motors are altogether different than d-c motors. Before
you begin the study of a-c motors, it would be a good idea to review the main points
on alternating current - the table at the end of Chapter 13 gives you a good outline
of a.c., its fields, and inductive action.
First, a.c. is NOT STEADY. Current is constantly rising and falling. Second,
current does not flow in ONE DIRECTION ONLY. A.c. is constantly reversing its direction
of flow. These two directions of flow are called POSITIVE and NEGATIVE in order
to distinguish one direction from the other.
Figure 156. - Series motor on a.c.
Don't get the idea that the negative current is any weaker than the positive
current - they're absolutely EQUAL in strength, and regardless of the a.c. reversing
direction, it does just as much work as d.c.
Alternating current, by reversing direction, produces constantly reversing flux.
This constantly REVERSES THE POLARITY of a-c coils. Furthermore, the flux around
an a-c coil is never steady - it is constantly expanding and contracting. This reversal
of direction and constant change of value in a.c. makes possible the MUTUAL INDUCTION
circuit. This is the first basic idea necessary to the understanding of a-c motors.
IDEA NO. 1 - MUTUAL INDUCTION IN A.C.
The first basic idea - MUTUAL INDUCTION-you are familiar with. (Review Chapter
13 for the introduction of this idea.) The important fact in mutual induction, is
that the INDUCED voltage in the secondary is always OPPOSITE to the APPLIED voltage
of the primary. Which means that every time the PRIMARY has POSITIVE current, the
SECONDARY has NEGATIVE current - and vice versa. This is not so complex - look at
figure 157. It shows two ordinary coils; P, the primary and S, the secondary.
Figure 157. - Mutual induction polarities.
The solid arrows show current directions when the primary is POSITIVE and the
broken arrows . show current directions when the primary is NEGATIVE. With a.c.,
the primary is positive half of the time and negative the other half of the time.
A NORTH pole appears at the top of the primary coil when the current is positive.
And when the primary is positive, the secondary is negative, and a SOUTH pole appears
at the top of the secondary coil. The other half of the time, the primary coil is
negative and has a SOUTH pole at its top. In short, a NORTH INDUCES A SOUTH, AND
A SOUTH INDUCES A NORTH. Check these polarities with the hand rule for coils.
Work the problems for yourself - it's the only way you'll become "good"
at using the hand rules. The coils of figure 157 make up a simple TRANSFORMER. And
the action of ALWAYS INDUCING OPPOSITE POLARITY ON THE SECONDARY is called the TRANSFORMER
PRINCIPLE or TRANSFORMER ACTION. Transformers are mutual induction devices for the
transfer of voltage from a primary circuit to a secondary circuit.
IDEA NO. 2 - POLYPHASE A.C.
The second basic idea that you must get straight before studying a-c motors
is POLYPHASE CIRCUITS. Polyphase means MORE THAN ONE TIME. The term comes from two
words - "poly," meaning MORE THAN ONE and "phase," meaning TIME.
Polyphase a.c. is produced by a special kind of alternator. For example, a two-phase
alternator (two "times") has two separate windings in the stator. Figure
158 shows the two windings-they are placed in the stator 90° apart. Now, imagine
that the rotor is turning. Notice that the Y windings are cut by the rotor's flux
AFTER the X windings are cut. This causes the induced voltages in the two windings
to have different TIMING. For the Two-phase system, there are TWO sets of TIMING
for the rise and fall and reversing of a.c.
Figure 159 shows a solid line for the graph of the X winding's voltage, and
a broken line for the graph of the Y winding's voltage. One cycle, produced by one
revolution of the rotor, is pictured for each phase.
Figure 158. - Two-phase alternator.
Like all scientific measurements, there is an accurate method for measuring
the OUT-OF-PHASENESS (out-of-timeness) of these two voltages. It is possible to
use a standard unit of time - the second. If the rotor is revolving at 60 revolutions
per second, each revolution, or cycle, takes 1/60th of a second. And, if you examine
the graphs carefully, you'll find that the Y voltage is exactly one-quarter of a
cycle behind the X voltage. One-quarter of 1/60th is 1/4th x 1/60th second, or 1/240th
second. Which means that the Y voltage is behind the X voltage by 1/240th second.
In other words - the voltages are 1/240th of a second out-of-phase.
Measuring in such small fractions of a second by mechanical means is a tough
job. In fact, if the unit becomes much smaller - like 1/500th second - it is well
nigh impossible to measure. A much more accurate and easier unit of measure is the
ELECTRICAL DEGREE. You know that a complete circle is 360°. And directly across
a circle, or from ONE POINT on a circle through the center to an OPPOSITE POINT,
is 180°. This gives you the definition for electrical degrees - a north pole and
a south pole are opposite and they are 180 ELECTRICAL DEGREES APART. Therefore,
ONE ELECTRICAL DEGREE IS 180TH OF THE DISTANCE BETWEEN A NORTH POLE AND THE NEXT
Figure 159. - Two-phase voltages.
How many electrical degrees from the north to the south of the rotor in figure
158? 180 ELECTRICAL DEGREES. How many electrical degrees all the way around-from,
north to south and back to north? 360 ELECTRICAL DEGREES. How many, degrees from
the north to half-way to the south? 90 ELECTRICAL DEGREES.
Using electrical degrees to measure phase, the X windings are 90 electrical
degrees from the Y windings, which is exactly the same as saying that the Y voltage
is 90° out-of-phase with the X voltage. How much simpler it is to think of "90°
out-of-phase" instead of "1/240th of a second out-of-phase." Both
have exactly the same meaning. The graphs of figure 159 can now be re-labeled, as
in figure 160, in electrical degrees. Note that 1/60th second becomes 360°,
and 1/240th second becomes 90°.
Figure 160. - Two-phase voltages-electrical degrees.
Graphs of a-c voltage like this are called SINE WAVES. Notice that the sine
waves tell you exactly how much the voltages are out-of-phase (out-of-time), AND,
the exact position of the coils in the alternator. If the sine waves are 90 electrical
degrees apart, then the coils of the alternator, which produced the voltages, are
90 electrical degrees apart.
From the two-phase system, it's an easy step to the three-phase alternator.
Figure 161 is a three-phase alternator. If you follow the leads of the three coils,
you'll find that they are 120° apart. Therefore, the voltages produced are 120°
out-of-phase. Sine waves of this three-phase system look like figure 162.
Figure 161. - Three-phase alternator.
Using the X voltage as a reference, the Y voltage is 120° behind the X and the
Z is 120° behind the Y. DO NOT FORGET THAT 120° MEANS A DEFINITE LENGTH OF TIME
- A DEFINITE FRACTION OF A SECOND.
Figure 162. - Three-phase voltages.
THE ROTATING MAGNETIC FIELD
Most of the large a-c motors are three-phase jobs. Their stators are constructed
exactly like the stator of a three-phase alternator (figure 161) - three separate
windings - each winding displaced 120° from the others. On each winding is impressed
one of the phases from a three-phase alternator.
Figure 163. - The rotating magnetic field.
Figure 163 shows two cross-sectional views of a part of a three-phase motor
stator. The current directions in A correspond to the instant marked A on the sine
waves. Likewise, the current directions in B correspond to the instant marked B
on the sine waves. Notice what happens - in A, the flux is forming a north pole
between the X and Z windings. Use your hand rule for each conductor to prove this.
In B, the current in the Z winding has changed direction and this MOVES THE POLE
to between the Z and Y windings. Notice that the Z current changed direction at
point, P. In short, the change in direction of current in one phase has caused the
flux field to shift around the surface of the stator. This shifting of flux is true
for all the other parts of the stator and also for all the other poles. It's also
true for cycle after cycle. The total effect is that A MAGNETIC FIELD MOVES AROUND
THE SURFACE OF THE STATOR. As each phase changes current direction the poles MOVE
the width of THAT PHASE. And this field rotates FAST. The changes within phases
take place every 1/360th of a second. In fact, it only takes 1/60th of a second
for the field to rotate COMPLETELY around this stator.
Let's make sure you've got this straight. In a three-phase motor winding, the
current in each phase reverses at regular intervals - thus reversing the polarity
of the phase windings. Because the phases reverse current in a regular pattern -
Y reverses, then Z reverses, then X reverses and so on repeating Y, Z, X, Y, Z,
X, etc. - the phases reverse polarity one after the other right around the stator
The rotating field is like the rotor magnet of the alternator which produced
it. The ROTOR spins around inside an ALTERNATOR stator. And the ROTATING MAGNETIC
FIELD spins around on the inside surface of a MOTOR stator. All three-phase motors
use this kind of stator. But the rotors are different, according to the type of
THE A-C INDUCTION MOTOR
This type of three-phase motor runs because of MUTUAL INDUCTION and a ROTATING
FIELD. The rotor has a short-circuited winding. And as the rotating field of the
stator sweeps across the rotor windings, A VOLTAGE IS INDUCED. The poles which are
produced in the rotor are from INDUCED current. Therefore, they are always OPPOSITE
to the poles on the stator, which induced them. What happens? Attraction occurs
between the stator and rotor poles. Since the stator poles are moving (rotating),
they tend to drag the rotor poles along. Torque is produced and the rotor rotates.
Figure 164. - The squirrel cage rotor.
This motor is called the SQUIRREL CAGE motor because of the construction of
its rotor. Figure 164 shows two views of the squirrel cage rotor. It consists of
an iron core mounted on a shaft. And there are copper bars running in slots the
length of this core. At each end, a copper END RING is welded to each and every
copper bar. This makes the rotor a certain SHORT CIRCUIT.
It is important that these rotors be absolute short circuits because they get
current ONLY by induction. There are no slip rings or commutator to feed current
into the rotor.
The squirrel cage ROTOR is like the secondary of a transformer. The stator is
like a primary. The rotor (secondary) gets its voltage by induction from the stator
The squirrel cage MOTOR has many advantages and is the most widely used and
popular motor in the world. It's cheap - the windings are easily set in place. It's
rugged - there are no slipping contacts to get out of order. It's safe - no sparks
to ignite gasoline or other explosives. This is one motor which can be run under
water. It makes no difference whether the water short circuits the rotor or not
- it's supposed to be a short anyway.
The WOUND ROTOR MOTOR embodies the same principles of operation as the squirrel
cage motor. But, wire windings' are used on the rotor of the wound rotor motor instead
of using copper bars. The leads of these wire windings are brought out to slip rings
where they are short circuited by a rheostat. Just as in the squirrel cage, a voltage
is induced in the rotor, current flows in the short circuit, and torque is produced
by the pull of the rotating field.
For certain jobs, where SPEED CONTROL and a GOOD START are necessary, the wound
rotor motor is better than the squirrel cage motor.
THE SYNCHRONOUS MOTOR
Another three-phase motor is the SYNCHRONOUS type. This motor is NOT an induction
motor. The stator is the regular three-phase rotating field job -but the rotor has
field poles ENERGIZED BY D.C. The d.c. is generated by a small generator called
an EXCITOR mounted on the end of the rotor shaft. This d.c. is fed into the rotor
by means of slip rings.
Figure 165 shows the end view of a four pole synchronous motor. Notice that
there are just as many poles on the rotor as on the stator. Every rotor south is
attracted to a stator north and vice versa. This attraction is the result of a magnetic
field between the stator and rotor and is called a MAGNETIC LOCK. As the stator
field rotates, the lock forces the rotor to turn with it.
Two Greek words - SYN meaning "together" and CHRONOS meaning "time"
make up the name, SYNCHRONOUS. SYNCHRONOUS describes the motor's speed - its rotor
always rotates just exactly as fast as the field of the stator-"together in
Figure 165. - Synchronous motor.
The synchronous motor is NOT a self-starting motor. Its rotor is heavy and,
from a dead stop, it is impossible to bring the rotor into magnetic lock with the
rotating field. For this reason, all synchronous motors have some kind of starting
device. A simple starter is another motor - either d.c. or of the induction type
- which starts the unloaded synchronous job and carries it up to about 90 percent
or 95 percent of speed. Then the starting motor is disconnected and the synchronous
motor PULLS INTO STEP with its magnetic lock. Another starting method is a second
winding of the squirrel cage type added to the rotor d-c windings. This induction
winding brings the motor almost up to speed by following the rotating field. Then
the d.c. is cut into the synchronous rotor and the rotor pulls into step. The latter
method is the most commonly used for starting synchronous motors.
Reversing any three-phase motor is a snap. Just interchange ANY TWO STATOR LEADS.
By doing so, the phases are interchanged. Z follows Y instead of following X in
the process of reversing polarity. The rotating magnetic field goes around the other
way. And the rotor follows it-the motor has reversed rotation.
These are the three types of THREE-PHASE MOTORS - SQUIRREL CAGE INDUCTION, WOUND
ROTOR INDUCTION AND SYNCHRONOUS. All three use exactly the same kind of stator but
their rotors are different. Notice that the NAME of the motor tells you what KIND
of a rotor is used.
Many years ago, two-phase motors were built - but today, it's not likely that
you'll ever see one. If you should happen to run across a two-phase job - outside
of F. C. equipment or an old ship - just remember that the types and principles
of operation are exactly like the three-phase motors.
Three-phase motors are the most efficient and all-around best motors built.
And if three-phase current were always available, you'd never see a single-phase
motor. But it takes a special kind of alternator to produce three-phase voltage.
And, when you can't get three-phase - single-phase must be used.
Here's what makes single-phase motors less efficient than three-phase - No rotating
magnetic field is set up by a single-phase current.
If a single-phase motor were built like a three-phase job, there would be induction
and opposite poles on the rotor all right-BUT-no ROTATING flux to drag the rotor
around. However, if the rotor once gets started, the rotor poles lag a little behind
the stator poles. And attraction is set up-torque is produced-the motor runs. Notice
that THE SINGLE-PHASE MOTOR HAD TO BE GIVEN A START BEFORE IT WOULD RUN.
Starting a motor by hand isn't bad if it's in an electric razor or electric
clock. But motors for general duty must be self-starting. And this is the whole
problem of single-phase jobs - HOW to make them self-starting. Each single-phase
motor is named from its starting method.
There are three general types of single-phase motors - the SERIES-UNIVERSAL
(at beginning of this chapter), the REPULSION-INDUCTION, and the SPLIT- PHASE. And
as you proceed, you will notice that, except for the series-universal, each has
a cutout device to remove the starting equipment from the circuit. And they all
run as straight induction jobs.
The REPULSION single-phase motor has a rotor that is wound just like a d-c drum
armature. Figure 166 shows a schematic of this motor. Notice that the BRUSHES ARE
CONNECTED TOGETHER. The only current in this rotor is induced by the expanding and
contracting single-phase field of the stator. The poles produced on the rotor are
located opposite the brushes. Because the brushes furnish the only complete circuit
for the current, they insure the pole position opposite their own position. The
self-starting of this motor DEPENDS ON THE BRUSH POSITION. In the drawing, the brushes
are correctly located for starting. Suppose you moved them. The rotor poles move
with the brushes because the brushes carry the current which makes the poles. Try
the brushes opposite the stator poles - rotor poles are in line with stator poles.
Torque? ZERO. The force is directly in line with the shaft. The motor will not start.
Suppose the brushes are moved to a position 90° from the position in the drawing.
Torque? Yes, but in a clockwise direction. You've REVERSED the motor.
Figure 166. - Repulsion motor.
Many of these repulsion motors have a short circuiting device connected with
a CENTRIFUGAL SWITCH. When the motor reaches about 75 percent of full speed, the
centrifugal switch lifts the brushes off the commutator AND short circuits all the
segments. The rotor is just like a squirrel cage job - short circuited. It continues
to run - but as an INDUCTION motor. The advantage of this short circuiting is a
saving in wear and tear on the commutator and brush system. After all, the brushes
and commutator were only put on the motor to start it - and once it gets going,
it will continue to run. And what is a CENTRIFUGAL SWITCH? It's a movable device
with a weight which whirls with the motor. When the force on this weight gets strong
enough, it flys out and throws the switch. Figure 167 shows a repulsion motor rotor
with a centrifugal switch. W is the weight and R is a rod attached to the weight.
C is a copper ring for short circuiting the commutator segments. When the weight
flys outward because of the increased speed, it pushes the rod forward. The rod
LIFTS THE BRUSHES and THE RING SHORTS THE SEGMENTS all in one operation.
Figure 167. - Repulsion rotor with centrifugal switch.
When a repulsion motor is equipped for short circuiting the rotor, it is called
a REPULSION-INDUCTION motor. The name comes from the fact that it starts on repulsion
and funs on induction. This is a fairly rugged motor - it's one of the best single-phase
a-c jobs. The only disadvantage is in the brush and commutator rig. It gets dirty
and is subject to wear and arcing. It's always best to use a motor WITHOUT slipping
contacts, if possible.
The single-phase motors without slipping contacts use a STARTING WINDING. The
winding is embedded in the stator slots next to, or over the top of, the main windings.
Figure 168 is the schematic diagram showing both main and starting windings. These
motors start by SPLITTING the single-phase current into two phases. A single-phase
current can be split into two phases by using either a high resistance circuit or
a condenser in one of the windings (at point A in figure 168). Then the current
in the winding that contains either the resistance or the condenser is out-of-phase
(out of time) with the current in the other winding. The two phases produce a weak
rotating magnetic field. And-with the rotating magnetic field, a short circuited
squirrel cage rotor produces torque.
Figure 168. - Split phase motor.
Notice the centrifugal switch in figure 168. It disconnects the starting winding
after the motor has picked up speed. This is always necessary in resistance type
starting. The winding would burn out, because of its high resistance, if it weren't
dis-connected as quickly as possible.
The chief advantage of these split-phase motors lies in their lack of commutators
and brushes. However, they usually have a poor torque at start-ing-which means that
they cannot be used on large loads.
You can reverse a split-phase motor by inter-changing any set of stator leads.
This is the same as reversing a three-phase job.
STARTERS FOR A-C MOTORS
D-c motors required starter rheostats for motors over 5 hp. A-c motors likewise
require some means of limiting current at start. But a-c motors can stand more current
without burning - usually only motors of 25 hp or more have starters. That's a good
thing because almost all single-phase motors are less than 25 hp. This eliminates
the necessity of starters on just about everything except three-phase jobs.
All starters have just one main job to do - cut down the current at the start.
This job can be done in three different ways. First, by a RESISTANCE. Second, by
a TRANSFORMER which reduces voltage across the stator and thereby reduces current
(I = E/R). Third, by a STAR-DELTA switch which changes the windings of the stator
from a parallel to a series connection (there is more resistance in a series connection).
Figure 169 is a schematic of a RESISTANCE STARTER. You can apply this schematic
to ANY starter. Just substitute transformers or a star-delta switch for the resistors.
Notice that three resistors are necessary - one for each phase. The switch is first
thrown DOWN. This puts the resistors in the lines. After the motor has built up
speed and it can stand more current, the switch is thrown UP, thereby cutting out
the resistance and putting the motor directly on the full line voltage.
Figure 169. - Resistance starter.
The MOTOR OVERLOAD RELAYS are interesting devices. They're simply solenoid coils
carrying the motor's current. The cores of the coils are attached to the overload
contacts. Suppose the motor is over-loaded - drawing too much current. It would
soon overheat and burn out if it were not for the relays. The excessive current
going through the overload relays sets up a field which pulls the cores up into
the coils. The contacts pop open and stop the motor. All of these relays have reset
buttons. When the reset buttons are pushed, the core returns to the normal position
and the contacts are reclosed.
The relay system is a better overload system than fuse protection. The relay
can be reset with the flick of a finger. And most overloads are temporary anyway
-y ou wouldn't want to replace fuses every time a motor got a momentary overload.
REMOTE CONTROL starters have the starting switch at some handy place. Lines
then run to the motor. For example, it's a lot easier to control a bilge pump from
the dynamo room, than to have to go down to the double bottoms to turn it on and
off. A remote control system simply lengthens the lines from starter switch to motor.
Chapter 16 Quiz