Here is the "Electricity - Basic Navy Training Courses" (NAVPERS 10622) in its entirety. It should provide one of the Internet's best resources for people seeking a basic electricity course - complete with examples worked out. See copyright. See Table of Contents.
¶ U.S. GOVERNMENT PRINTING OFFICE; 1945 - 618779
Generators are electrical PUMPS. Motors are electrical WORKERS: There are many
kinds of work done by electrical motors - turning fan blades, running hydraulic
pumps, turning rudders, training and elevating guns, and sometimes turning the propellers.
Everyone of these jobs consumes MECHANICAL power. And that tells you what an electric
motor is - a device for changing ELECTRICAL POWER into MECHANICAL POWER.
Many men want to know why it is necessary to change the form of power, time
after time, in order to get a job done. They want to know why it is necessary to
switch from mechanical to electrical and then back to mechanical power. There are
a number of reasons why - and all of them good reasons.
Suppose the anchor winches, blowers, pumps, and elevators of a ship were operated
by steam engines instead of electrical motors. It's not a bad idea, because it would
eliminate all the troubles of changing mechanical power to electrical power in turbo-generators
and then changing the electrical power back to mechanical power in motors. This
electrical system looks like a wasteful proposition. Every change of- power is at
an efficiency less than 100 percent, so it involves some loss. If it's wasteful,
then, why use it? Because ELECTRICAL POWER IS THE EASIEST AND SAFEST KIND OF POWER
But to get back to the anchor winch. Running a steam pipe to the anchor winch
cuts through many bulkheads and decks. Watertight integrity is upset. But, an electric
cable can make the same run and the kickpipes and stuffing tubes through decks and
bulkheads PRESERVE watertight integrity. Suppose enemy fire bursts a steam line
between the boiler and the steering engines. Power is drained off the boilers and
men may be scalded by escaping steam - things are really fouled up. Sure - an electric
cable in the same position would be broken too. But what happens? Probably an open
Circuit results which does not drain power and does not injure anyone. The worst
that could happen would be a short circuit, in which case fuses or circuit breakers
would quickly open the circuit rendering it harmless. There are many reasons for
using electrical motors - they're safe, handy, easily controlled, and easily supplied
HOW A MOTOR IS BUILT
This is easy-a motor is built just like a generator. The overall name for motors
or generators is DYNAMO. If the shaft of a dynamo is connected to a prime mover
and turned - it's a GENERATOR - it pumps electrical power OUT on its lines. If the
shaft of a dynamo is connected to a mechanical load - it's a MOTOR - it takes
electrical power IN on its lines.
HOW IT WORKS
In the study of Lenz's law you learned that a current carrying conductor in
a magnetic field exerts a force against the field. The force tends to push the conductor
out of the field. This is the principle of operation of the motor.
The magnetic field is furnished by the pole pieces and frame. As in the generator,
the field is stationary and steady. Current is sent into the armature windings and
sets up a magnetic field around the armature. The two fields - armature and frame
- react against each other. The result is a force against the armature windings
which tends to push them out of the field. Since these windings are fastened to
the armature core and shaft, they tend to move out of the field also.
UNDERSTANDING MOTOR ACTION
If one strand of wire is suspended between the . poles of a horseshoe magnet,
as in figure 137, nothing happens. But close the switch, connecting the batteries
to the wire, and the wire jumps backwards, into the magnet. Reverse the switch so
that current direction in the wire is reversed and the wire jumps outwards away
from the magnet. This is proof that there is a FORCE EXERTED ON A CURRENT CARRYING
CONDUCTOR. The conductor tends to be pushed-out of the field. It is also proof that
the direction of push reverses when the current is reversed. As you probably suspect-the
direction of push also reverses when the pole pieces change polarity.
Figure 137. - Conductor in a magnetic field.
Figure 138 summarizes motor action. Notice, in the A drawings, that the flux
above the conductor blends with the flux of the field.
Figure 138. - Motor action.
The flux below the conductor cancels the field flux. This results. in a strong
but distorted field ABOVE and a weak field BELOW. The conductor moves downward into
the weakest area. In B, the current is reversed - the field below is strong and
distorted, and the field above is weak. The conductor moves upward.
Evidently, motor action is the result of two magnetic fields reacting on each
other. It's a lot like two south or two north poles repelling each other -if one
of the poles is free to move, a simple motor action is produced. After all, a compass
needle reacting in a magnetic field is like a tiny motor.
Figure 139. - Applications of the motor hand rule.
THE MOTOR HAND RULE
Just like generators, motors have three "directions" - conductor current
direction, field, flux direction, and direction of motion. And again, they are linked
together by a hand rule. The thumb stands for the motion of the conductor. The first
finger for flux direction and the middle finger for the current direction in the
conductor. But here's a change - FOR MOTORS YOU USE THE RIGHT HAND. Figure 139 will
give you some practice in the motor hand rule. In A and B you must determine the
direction that the conductor will move. In C and D, determine the direction of current
necessary to, produce the motion indicated.
REMEMBER YOU USE THE FINGERS OF YOUR RIGHT HAND FOR MOTORS EXACTLY THE SAME
AS YOU USED THE FINGERS OF YOUR LEFT HAND FOR GENERATORS.
NOTE - The Warning given on page 140 applies here also.
Figure 140. - Answers.
Figure 140 gives you the correct answers for figure 139. Try the motor hand
rule on ALL the diagrams before you check any of your answers.
LOOP IN A FIELD
The simplest motor would be a wire in a magnetic field with a mechanical load
attached. Every time the circuit was closed, the wire would move, dragging its load
with it. When the circuit was reversed, the wire would reverse and push its load
back again. This kind of a motor is impractical. In the first place, it's too weak
to do much work. And in the second place, straight line, back and forth motion is
inefficient and slow.
To increase the strength, add more conductors so that the forces add. To eliminate
the straight line motion, make the set of inductors rotate. Here's how it's done.
A single-turn coil is mounted in a magnetic field as in figure 141. Note that the
current direction is traced by arrows. The left-hand side of the coil is carrying
current IN. And the motor hand rule tells you that this side moves DOWNWARD. The
right-hand side of the coil carries current OUT. And the motor hand rule indicates
motion UPWARD. The small drawings, just below each coil side, shows what happens
to the flux at each side. Now, if the right side moves up, the left side moves down
and the coil is pivoted along its center line - counterclockwise rotation is produced.
The forces against these conductors are straight line forces but because the
coil is pivoted, they can't move in a straight line. They are obliged to move in
a curve - a part of a circle. When a force produces a circular or twisting motion,
the result is called a TORQUE.
Figure 141. - One loop motor action - 1.
The torque on this loop continues until it is in the position shown in figure
142. In figure 142, the coil is in the neutral plane - no torque is produced. The
segments on the commutator are breaking contact with their brushes. Current is about
to reverse in the coil by switching brush connections. Even if the brushes were
not breaking contact, the torque would be zero-because the upward and downward forces
cannot produce rotation from this position. The forces are alined with the pivoting
shaft. No twist - no torque. Will the coil stop on the neutral plane? Only if it
is turning very slowly. Usually the momentum is great enough to carry the coil through
the neutral plane. Just past the neutral plane the segments switch brushes. This
reverses the coil current.
Figure 142. - One loop motor action - 2.
Figure- 143. - One loop motor action - 3.
Examine figure 143 - the motor hand rule will tell you that the white side of
the coil is now forced downward and the black side upward. This keeps the coil rotating
in a counterclockwise direction. The total effect of all the forces operating on
the coil has been to produce a torque in a counterclockwise direction.
One coil turning in a field is a motor all right - but the load it is capable
of driving is EXTREMELY small. Furthermore, every time the coil passes through the
neutral plane, the torque is zero. This zero point introduces a jerk to the rotation.
All you have to do to make the motor stronger and to eliminate the zero torque points,
is simply add another coil at right angles to the first.
Figure 144. - Two loop motor action.
Look at figure 144. With two coils arranged like this, only the coil in• the
best position to produce torque is connected to the brushes. The power is doubled
and the points of zero torque are eliminated.
The next step is the use of the Gramme ring. armature as a motor. Figure 145
shows both the current direction and the force exerted by each winding. Notice that
each conductor exerts a force which tends to turn the armature clockwise. As a generator,
only the OUTSIDE conductors of the Gramme ring cut flux and produced voltage. Likewise,
as a motor, only the OUTSIDE wires are acted on by the field flux. In fact, there
isn't any flux to act on the inside conductors - it all enters the ring and
travels through the iron when going from north pole piece to south pole piece. Figure
146 shows a cross section of a Gramme ring. Notice the flux path and the force vectors.
Use your motor hand rule on a few conductors on each side of the armature. Prove
to yourself that the armature rotates clockwise.
Figure 145. - Gramme ring motor action.
Figure 146. - Cross section of the Gramme ring.
ST. LOUIS TYPE MOTOR
The ST. LOUIS type motor of figure 147 is not a commercial job. Yet it clearly
illustrates motor action. Note the two circuits-one through the field poles, the
other through the armature. Both circuits do the same thing-each sets up an electromagnetic
field. The two fields set up four forces between the armature poles and the field
poles. The north pole of the armature is attracted to the south pole of the field
and is repelled by the north pole of the field. The south pole of the armature is
attracted to the north pole of the field and repelled by the south pole of the field.
Two attractions and two repulsions-all four pushing in one rotational direction.
Figure 148 shows the four forces as vectors.
Figure 147. - St. Louis motor.
Figure 148. - Torque vectors in the St. Louis motor.
Notice that all vectors are in a clockwise direction - all vectors produce clockwise
rotation. You would expect the armature to stop when the armature poles and the
field poles are opposite each other (second position of figure 147). It would, EXCEPT
for two reasons. FIRST, the brush connections change segments thus reversing the
polarity of the armature. Repulsion and attraction exchange positions. SECOND, the
momentum of the armature carries it past the DEAD-CENTER position, opposite the
poles. If the motor stops at dead-center, it won't be self-starting again because
the forces of attraction and repulsion are on a straight line through the shaft.
You would have to give it a whirl by hand, so that the armature and field poles
are at an angle. Torque is produced only when the forces of the two fields are at
an angle to the armature shaft.
The drum winding for a motor is just like the drum winding for a generator.
It is exactly like the armature in figure 133. Another way to picture this armature
is by cross section as in figure 149. This figure shows many interesting details
of design. Notice that EVERY conductor is on the OUTSIDE of the drum. This means
that EVERY conductor is in the flux field and that EVERY conductor exerts a torque.
The conductors are set in armature SLOTS and LOCKED in place by insulating wedges.
Why? Because the force of electromagnetism on these conductors is tremendous, especially
in large motors. If they weren't locked in, they'd be torn off the armature by this
force. The motor action of a conductor in a field is a STRAIGHT LINE force - the
conductor tends to move directly out of the field. By locking it on the armature
core, the conductor is forced to drag the armature around with it when motor action
takes place. Also, examine the locking "methods between the shaft and core.
The shaft is locked by a key to the iron core. Thus, windings, core, and shaft are
one mechanical unit turning together.
Figure 149. - Cross section of drum winding.
In general, motors are designed and constructed to do just one job-convert the
electrical energy of their fields into the mechanical energy of their shafts. There
are many modifications of design and several different methods of connection but
they all work on the principle THAT A CURRENT CARRYING CONDUCTOR IS FORCED OUT OF
A MAGNETIC FIELD. The more complex designs and connections which are set up for
specific jobs are explained in the books for specific ratings.
MOTOR ACTION IN A GENERATOR
What's the difference between a windmill and a blower-fan? Both are constructed
of a number of blades which handle wind. In CONSTRUCTION there's no difference.
But, in PURPOSE OR USE, there's plenty of difference. A WINDMILL is TURNED BY MOVING
AIR and its mechanical power output is used to pump water. A BLOWER-FAN is turned
by a motor or an engine and its power output IS USED TO MOVE AIR. Construction is
the same -but what they DO depends on HOW they're used.
What's the difference between a motor and a generator? In construction - there's
no difference. In use - there's plenty of difference. Now, the point is - why doesn't
the generator act like a motor and why doesn't the motor act like a generator? THEY
DO! Remember, or if you've forgotten - review it - the description of a welding
generator in Chapter 13. When a load is thrown on this generator, the prime mover
whines and shows, that it's working against a load. This load is the GENERATOR TRYING
TO RUN AS A MOTOR. And the higher the current through the generator (greater load),
the harder it trys to run as a motor.
Look at figure 150. This is a cross section of a GENERATOR. Using the generator
hand rule, you see that the current in the windings is induced by CLOCKWISE rotation.
If there's current in the windings - and there certainly is-those windings are -going
to set up fields just like the windings of a motor. Using the motor hand rule, you
see that the generator is trying to run as a MOTOR in a COUNTERCLOCKWISE direction.
Figure 150. - Motor action in a generator.
The total picture is this - the prime mover is rotating the generator in a clockwise
direction, and the fields set up by the induced currents in the armature windings
attempt to drive the generator as a motor in a counterclockwise direction. This
tendency to oppose the prime mover is called MOTOR ACTION IN A GENERATOR. The higher
the current in the armature windings, the stronger the motor action.
COUNTER-EMF IN A MOTOR
Now, how about motors? Do they generate a voltage? Indeed they do, and it's
a good thing they do! Motors would burn up if they didn't induce a voltage in the
Look at figure 151. This is the generator of figure 150 now being used as a
MOTOR. You notice that, although the current of the armature is the same in both
figures, the rotation is opposite. That should be expected - 150 is a generator
and 151 is a motor. As you know, the fields set up around the conductors on the
armature react with the fields set up by the pole pieces. Torque is produced and
the motor rotates counterclockwise. Check it with the motor hand rule.
Figure 151. - Generator run as a motor.
As the armature rotates, ITS CONDUCTORS CUT THROUGH THE FIELD FLUX. A voltage
is induced in these conductors. Using the generator hand rule for this GENERATED
voltage you'll find that it is OPPOSITE to the voltage APPLIED at the brushes. Figure
152 shows the direction of the applied volt-age and the direction of the generated
voltage. The generator and motor hand rules tell you that the generated and applied
voltages in a motor are ALWAYS OPPOSITE.
The generated voltage in a motor is called COUNTER-ELECTROMOTIVE FORCE. This
means that there are two voltages operating on every conductor on the armature of
a motor. Moreover, these two voltages are opposing each other. Current, then, is
the result of a combination of the two voltages. It is possible to prove that the
COUNTER-EMF IS ALWAYS LESS THAN THE APPLIED EMF.
Say that the armature of figure 152 has a resistance of 0.5 ohm. The applied
voltage is 110 volts. This is what happens when the switch is closed.
Figure 152. - Direction of counter-emf.
WHAM! - 110 volts pushing current through 0.5 ohms resistance.
I = E/R = 110/0.5 = 220 amps.
This 220 amperes of current flowing through the small windings of an armature-IT
WOULD REALLY COOK! But, wait - is there a current of 220 amperes in this armature?
Yes, there is-but ONLY AT THE INSTANT OF STARTING. As soon as the armature starts
to turn, it produces a counter-emf, opposite to the 110 volts of applied emf. When
it is turning at one-quarter speed, the counter-emf is 25 volts. The NET VOLTAGE
across the armature is 110 volts minus 25 volts or 85 volts - the voltages are SUBTRACTED
because they are OPPOSITE. The 25 volts of counter-emf cancels 25 volts of the applied
emf, leaving 85 volts to push current. Now the current through the armature is -
I = E/R = 85/0.5 = 170 amps.
Still very much too high, but getting smaller!
At one-half speed, the counter-emf is 50 volts, the net voltage is 110 - 50
= 60 v., and the current is -
I = E/R = 60/0.5 = 120 amps.
Current value is dropping as counter-emf In-creases!
At three-quarters speed, the counter-emf is 75 volts, and the current is -
I = E/R = 35/0.5 = 70 amps.
This is getting close to a safe value!
At full speed the counter-emf is 100 volts and current is -
I = E/R = 10/0.5 = 20 amps.
Current is at a normal, safe value!
Why did the counter-emf become stronger as the speed increased? BECAUSE MORE
LINES WERE CUT PER SECOND AS THE SPEED INCREASED. This connection between speed
and counter-emf is a perfect current control. When the motor is going SLOW it needs
a HIGH current in its armature. The high current makes a strong field and the motor's
torque drives it to a higher speed. As the speed increases the counter-emf also
increases, and the net voltage becomes less. This causes the current to decrease
- AND THAT'S JUST RIGHT. Because, as speed in-creases, the motor doesn't need as
strong a torque to increase or maintain its speed. Finally, when the motor reaches
full speed, the torque and consequently armature field) that is needed, is relatively
small. The counter-emf at full speed is high and allows just enough current to pass
through the armature to maintain speed.
From this example, two facts stand out - THE COUNTER-EMF IS DIRECTLY PROPORTIONAL
TO SPEED. THE ARMATURE CURRENT DECREASES AS THE COUNTER-EMF INCREASES.
LOADING A MOTOR
Imagine that the motor just studied is rotating at a full speed of 4,000,and
is driving a water pump. The pump is delivering 100 gallons of water per second.
Now you double the load by connecting to a pump delivering 200 gallons of water
per second. Of course you first make sure that the motor is LARGE enough to handle
the additional load. With the doubled load, the motor needs twice as much power
and it gets it by counter-emf adjustment. Here's how it works - with the doubled
load, the motor slows down to 3,600 rpm, and at this speed, the counter-emf is only
90 volts. The net voltage increases from 10 volts to 110 - 90 = 20 volts. At 20
volts net voltage, the current is -
I = E/R = 20/0.5 = 40 amps.
Or, exactly TWICE AS MUCH CURRENT TO HANDLE TWICE AS MUCH LOAD.
Here is the formula for determining the armature current -
Ia = (Ea - Eg)/Ra
Ia = the armature current, in amperes;
Ea = the applied voltage, in volts;
Eg = counter-emf, in volts;
= resistance of the armature, in ohms.
Notice that his formula is a form of Ohm's law. The E in Ohm's law has been
Ea - Eg because this is the ACTUAL VOLTAGE FORCING
Counter-emf is like a valve in a water pipe. If you want a lot of water, you
open the valve. If you want a little water, you partially close the valve. If a
motor needs a lot of current to handle its load, it slows down thereby decreasing
the counter-emf and allowing a high current into the armature. If a motor needs
only a little current, it speeds up so that the counter-emf is just the right value
to let enough current through the armature to handle the load.
You might say that this is like the transmission in an automobile. Low gear
gives the most torque but the lowest speed. High gear gives the highest speed but
the least torque. In a motor high speed means high counter-emf and low current and
torque (light loads). Low speed means low counter-emf and high current and torque
The motor of figure 153 has 550 amperes through its armature at the instant
of starting. If it started very quickly and built up speed, the counter-emf would
choke off this high current before any damage is done to the windings. But large
motors are too heavy to start quickly-it takes time to build up speed and counter-emf.
You can't get a motor- - . cycle pickup out of a five-ton dump truck! Therefore,
large motors get altogether too much current at the start. To cut down this starting
current, a rheostat is connected in series with the armature. When the motor is
started, the resistance is cut in-limiting the current to a safe value. As the speed
picks up, the resistance is gradually cut out of the circuit because the counter-emf
is taking its place in reducing current. Figure 153 shows a 7% hp motor with a STARTING
RHEOSTAT. All the electrical values, are labeled. If this motor were , started without
the resistance, the armature current would be -
Ia = (Ea - Eg)/Ra
= (220 - 0)/0.4 = 550 amps.
and NORMAL full load current is only about 40 amperes. You KNOW the damage that
would result from this excessive current.
Figure 153. - Motor with starting rheostat.
The rheostat in series with the armature has a resistance of 1 ohm per unit.
When the motor is started all five units are cut in, and the current is -
I = E/R = 220/5.4 = 40.7 amps.
As the speed of the motor increases the rheostat arm is moved progressively
from point 5 to point 0, thus cutting down the added resistance from 5 ohms to zero
as the counter-emf builds up. To put it briefly - the rheostat simply takes the
place of the counter-emf when the counter-emf is too low to do its own job of limiting
the armature current.
When rheostats are combined with certain other pieces of electrical apparatus,
they are called STARTERS. Starters are used for ALL d-c motors over 5 hp and for
almost all motors between 1 hp and 5 hp. Usually no starter is used on small motors
- under 1 hp.
The most important function of starters is to limit the armature current by
a rheostat. Other functions of a starter are explained wherever needed in the books
for specific ratings.
Compare the four motors shown in figure 154. A and B have their armature currents
in opposite direction. Using the motor hand rule, you'll find that their rotations
are opposite. The currents in the field windings of C and D are opposite, therefore
their field polarities are opposite.
Figure 154. - Reversing motors.
Using the motor hand rule, you'll find that their rotations are also opposite.
Finally, compare A and D. The fields of these two motors are opposite. Also, the
currents in their armatures are opposite. But the motor hand rule shows that A and
D have the same rotational direction.
Thus, you can reverse the direction of rotation of a motor by either reversing
the armature current or reversing the field current. But NOT by reversing BOTH armature
and field. Navy methods call for ALWAYS reversing the armature current in order
to reverse rotation.
Here's a tip-the easiest way to reverse the current direction in any winding
is simply by reversing the lead connections.
Chapter 15 Quiz