Navy Electricity and Electronics Training Series (NEETS)
Module 12—Modulation Principles
Chapter 2: Pages 2-51 through 2-60
Module 12—Modulation Principles
Pages i - ix
1-1 to 1-10
, 1-11 to 1-20
1-21 to 1-30
, 1-31 to 1-40
1-41 to 1-50
, 1-51 to 1-60
1-61 to 1-70
, 1-71 to 1-75
2-1 to 2-10
,2-11 to 2-20
2-21 to 2-30
, 2-31 to 2-40
2-41 to 2-50
, 2-51 to 2-60
2-61 to 2-64
, 3-1 to 3-10
3-11 to 3-20
, 3-21 to 3-30
3-31 to 3-35
AI-1 to AI-6, Index-1 to 2, Assignment 1 , 2
a usable reconstructed modulation curve. At the sampling rate of figure 2-50 and with a 4-element binary code, 128 bits (presence or absence of pulses) must be transmitted for each cycle of the modulating frequency. At the sampling rate of figure 2-51, only 32 bits are required; at the minimum sampling rate, only 8 bits are required.
Figure 2-51.—Pulse-code modulation of a quantized wave (32 bits).
As a matter of convenience, especially to simplify the demodulation of PCM, the pulse trains actually transmitted are reversed from those shown in figures 2-49, 2-50, and 2-51; that is, the pulse with the lowest binary value (least significant digit) is transmitted first and the succeeding pulses have increasing binary values up to the code limit (most significant digit). Pulse coding can be performed in a number of ways using conventional circuitry or by means of special cathode ray coding tubes. One form of coding circuit is shown in figure 2-52. In this case, the pulse samples are applied to a holding circuit (a capacitor which stores pulse amplitude information) and the modulator converts PAM to PDM. The PDM pulses are then used to gate the output of a precision pulse generator that controls the number of pulses applied to a binary counter. The duration of the gate pulse is not necessarily an integral number of the repetition pulses from the precisely timed clock-pulse generator. Therefore, the clock pulses gated into the binary counter by the PDM pulse may be a number of pulses plus the leading edge of an additional pulse. This "partial" pulse may have sufficient duration to trigger the counter, or it may not. The counter thus responds only to integral numbers, effectively quantizing the signal while, at the same time, encoding it. Each bistable stage of the counter stores ZERO or a ONE for each binary digit it represents (binary 1110 or decimal 14 is shown in figure 2-52). An electronic commutator samples the 20, 21, 22, and 23 digit positions in sequence and transmits a mark or space bit (pulse or no pulse) in accordance with the state of each counter stage. The holding circuit is always discharged and reset to zero before initiation of the sequence for the next pulse sample.
Figure 2-52.—Block diagram of quantizer and PCM coder.
The PCM demodulator will reproduce the correct standard amplitude represented by the pulse-code group. However, it will reproduce the correct standard only if it is able to recognize correctly the presence or absence of pulses in each position. For this reason, noise introduces no error at all if the signal-to-noise ration is such that the largest peaks of noise are not mistaken for pulses. When the noise is random (circuit and tube noise), the probability of the appearance of a noise peak comparable in amplitude to the pulses can be determined. This probability can be determined mathematically for any ration of signal-to-average- noise power. When this is done for 10 5 pulses per second, the approximate error rate for three values of signal power to average noise power is:
17 dB — 10 errors per second
20 dB — 1 error every 20 minutes
22 dB — 1 error every 2,000 hours
Above a threshold of signal-to-noise ration of approximately 20 dB, virtually no errors occur. In all other systems of modulation, even with signal-to-noise ratios as high as 60 dB, the noise will have some effect. Moreover, the PCM signal can be retransmitted, as in a multiple relay link system, as many times as desired, without the introduction of additional noise effects; that is, noise is not cumulative at relay stations as it is with other modulation systems.
The system does, of course, have some distortion introduced by quantizing the signal. Both the standard values selected and the sampling interval tend to make the reconstructed wave depart from the original. This distortion, called QUANTIZING NOISE, is initially introduced at the quantizing and coding modulator and remains fixed throughout the transmission and retransmission processes. Its magnitude can be reduced by making the standard quantizing levels closer together. The relationship of the quantizing noise to the number of digits in the binary code is given by the following standard relationship:
n is the number of digits in the binary code
Thus, with the 4-digit code of figure 2-50 and 2-51, the quantizing noise will be about 35 dB weaker than the peak signal which the channel will accommodate.
The advantages of PCM are two-fold. First, noise interference is almost completely eliminated when the pulse signals exceed noise levels by a value of 20 dB or more. Second, the signal may be received and retransmitted as many times as may be desired without introducing distortion into the signal.
Q-27. Pulse-code modulation requires the use of approximations of value that are obtained by what process?
Q-28. If a modulating wave is sampled 10 times per cycle with a 5-element binary code, how many bits of information are required to transmit the signal?
Q-29. What is the primary advantage of pulse-modulation systems?
Now that you have completed this chapter, a short review of what you have learned is in order. The following review will refresh your memory of angle modulation and pulse modulation.
FREQUENCY-SHIFT KEYING (FSK) is similar to CW keying in amplitude modulation and is a form of angle modulation. The carrier frequency is changed between two discrete values by the opening and closing of a key.
In FREQUENCY MODULATION (FM) the instantaneous frequency of the radio-frequency wave is varied in accordance with the modulating signal; the amplitude of the radio-frequency wave is kept constant.
MODULATION INDEX is the ratio of the maximum frequency difference between the modulated and the unmodulated carrier, or between the deviation frequency and the modulation frequency.
The number of SIGNIFICANT SIDEBANDS and the modulating frequency will determine the bandwidth of the fm wave. The number of significant sidebands can be determined from the modulation index.
The REACTANCE-TUBE MODULATOR is frequency modulated by using a reactance tube in shunt with the tank circuit.
The SEMICONDUCTOR-REACTANCE MODULATOR is used to frequency modulate low-power semiconductor transmitters.
The MULTIVIBRATOR MODULATOR uses an astable multivibrator with a modulating voltage inserted in series with the base return of the multivibrator transistors.
The VARACTOR FM MODULATOR uses a VARACTOR. This is a specially designed diode that has a certain amount of capacitance between the junction that can be controlled by reverse biasing.
In PHASE MODULATION the carrier’s phase is caused to shift at the rate of the modulating audio. The amount of phase shift is controlled by the amplitude of the modulating wave.
A BASIC PHASE MODULATOR may be a single tube in series with a capacitor to form a phase-shift network. As the impedance of the tube changes, the phase of the output shifts.
PHASE-SHIFT KEYING (PSK) is similar to CW and FSK. It consists of phase reversals of the carrier frequency as modulating signal data elements open and close the modulator key.
PULSE MODULATION is modulation in which we allow oscillations to occur for a given period of time only during selected intervals.
PULSE-REPETITION TIME (PRT) is the specific time period between each group of RF pulses.
PULSE-REPETITION FREQUENCY (PRF) is found by dividing the pulse repetition time into 1. This defines how often the groups of pulses occur.
PULSE WIDTH (PW) or PULSE DURATION (PD) is the time that a pulse is occurring.
REST TIME (RT) is the time referred to as nonpulse time.
PEAK POWER is the maximum power during a pulse.
AVERAGE POWER equals the peak power averaged over one complete cycle.
DUTY CYCLE is the ratio of working time to total time, or the ratio of actual transmit time to transmit time plus rest time, for intermittently operated devices.
The SPARK-GAP MODULATOR consists of a circuit for storing energy, a circuit for rapidly discharging the storage circuit, a pulse transformer, and a power source.
The THYRATRON MODULATOR is an electronic switch which requires a positive trigger of only 150 volts. The trigger must rise at the rate of 100 volts per microsecond to fire or cause the modulator to conduct.
Introduction to Matter, Energy, and Direct Current,
to Alternating Current and Transformers, Introduction to Circuit Protection,
Control, and Measurement
, Introduction to Electrical Conductors, Wiring Techniques,
and Schematic Reading
, Introduction to Generators and Motors
Introduction to Electronic Emission, Tubes, and Power Supplies,
Introduction to Solid-State Devices and Power Supplies
Introduction to Amplifiers, Introduction to
Wave-Generation and Wave-Shaping Circuits
, Introduction to Wave Propagation, Transmission
Lines, and Antennas
, Microwave Principles,
, Introduction to Number Systems and Logic Circuits, Introduction
to Microelectronics, Principles of Synchros, Servos, and Gyros
Introduction to Test Equipment
, Radar Principles,
The Technician's Handbook,
Master Glossary, Test Methods and Practices,
Introduction to Digital Computers,
Magnetic Recording, Introduction to Fiber Optics