Homepage - RF Cafe
Webmaster: Kirt Blattenberger | KB3UON | Sitemap | ©1996-2014
Menu below is just a small sample of what is here!
 
Custom Search
More than 10,000 searchable pages indexed.
•−•  ••−•    −•−•  •−  ••−•  •
RF Cafe Morse Code >Hear It<

What Causes Opamps to Blow? - RF Cafe Forums

Because of the high maintenance needed to monitor and filter spammers from the RF Cafe Forums, I decided that it would be best to just archive the pages to make all the good information posted in the past available for review. It is unfortunate that the scumbags of the world ruin an otherwise useful venue for people wanting to exchanged useful ideas and views. It seems that the more formal social media like Facebook pretty much dominate this kind of venue anymore anyway, so if you would like to post something on RF Cafe's Facebook page, please do.

Below are all of the forum threads, including all the responses to the original posts.


ifatfat
Post subject: What Causes Opamps to Blow? Posted: Tue Oct 07, 2008 5:00 am

Lieutenant

Joined: Tue Oct 07, 2008 4:56 am
Posts: 3
A big hi to everyone...

I would like to know what causes opamps to blow?

If I have a non-inverting amplifier, and I have the output constantly hitting the power rails, would it cause the opamp to blow?

Thanks in advance!


Top

darcyrandall2004
Post subject: Posted: Tue Oct 07, 2008 10:50 pm

Colonel


Joined: Tue Feb 27, 2007 6:16 am
Posts: 46
Hello,

The opamp will amplify the difference between its input terminals. The output can not exceed the power rails.

If the op amp amplifies the difference between its input terminals and the output does reach the power rail voltage, it will not be destroyed as a result of this.

If your opamp is blowing up, I think you will find that the output reaching the rail voltage is only a sympton not a cause.

Cheers

_________________
Regards, Darcy Randall, Perth, Western Australia


Top

ifatfat
Post subject: Posted: Tue Oct 07, 2008 11:15 pm

Lieutenant

Joined: Tue Oct 07, 2008 4:56 am
Posts: 3
Hi...

Thanks for the reply!

I'm wondering what might cause the opamps to blow? I'm not 100% sure... but I guess excessive current at the input might blow the amps? Are there other stuff I should look out for?


Top

IR
Post subject: Posted: Tue Oct 07, 2008 11:56 pm

Site Admin


Joined: Mon Jun 27, 2005 2:02 pm
Posts: 373
Location: Germany
An excessive output current can cause the op-amp to blow, this can happen if the amplifier drives a load which is too small.


Top

nubbage
Post subject: Posted: Wed Oct 08, 2008 4:18 am

General


Joined: Fri Feb 17, 2006 12:07 pm
Posts: 218
Location: London UK
Hi
I agree with both diagnoses and add that the differential voltage at the inputs has a spec that should not be exceeded, and I have had trouble like this in the past due to excessive voltage spikes on one of the two inputs that resulted in this spec being exceeded for a few microseconds. This led to unpredictable consequences within the structure, basically "punch through" that resulted in thermal run-away and permanent unrecoverable damage. Put a good scope on all interface pins and take a look.


Top

yendori
Post subject: Posted: Wed Oct 08, 2008 10:19 am

General


Joined: Thu Sep 25, 2003 1:19 am
Posts: 50
Location: texarcana
What IR said.


Top

ifatfat
Post subject: Posted: Thu Oct 09, 2008 8:08 pm

Lieutenant

Joined: Tue Oct 07, 2008 4:56 am
Posts: 3
Thanks for all the replies!

The output of the op amp circuit is going into a 0.01uF cap followed by a 50ohm resistor in series. How do I determine if this 50ohm is too small a load for the op amp to drive?

In the schematic design, the resistor to ground at the negative input is absent, so there's only a resistor in the feeback loop (from output to negative input). Would this design cause a problem?

nubbage, currently there's a resistor to ground that's parallel to the positive input. Would adding a cap in parallel to this resistor (to ground too) help out with the sudden voltage spikes?


Top

IR
Post subject: Posted: Fri Oct 10, 2008 4:31 pm

Site Admin


Joined: Mon Jun 27, 2005 2:02 pm
Posts: 373
Location: Germany
From your description, it looks like you are using your op-amp as buffer.

The absence of the resistor to ground should not cause a problem.
This resistor is used to set the gain of the op-amp in non-inverting configuration.

You can determine if the load is too low by simply finding out from the data sheet the maximal output current that the op-amp is capable to source/sink. By dividing the output voltage to 50-ohm, you will see if the current exceeds the value mentioned in the data sheet.


Top

nubbage
Post subject: Posted: Mon Oct 13, 2008 4:58 am

General


Joined: Fri Feb 17, 2006 12:07 pm
Posts: 218
Location: London UK
Hi
It is difficult to advise regarding spike suppression without knowing the exact application. A spike has a frequency spectrum, parts of which may overlap the bandwidth of your input signal.
In such circumstances it is possible to low-pass filter the input using a small passive element LC filter, so that the spike spectrum and the wanted signal are frequency-separated. Many circuits I have seen also use a degree of capacitive shunt across the gain-controlling feedback resistor acting as a kind of integrator, an integrator being a kind of low-pass filter.
Putting a good high frequency hi impedance oscilloscope across the input, the inverting input, the power rail, and the output should reveal if spikes are the problem.


Top

Philip_WNL
Post subject: Posted: Fri Oct 31, 2008 1:29 am

Lieutenant

Joined: Thu Oct 30, 2008 2:16 am
Posts: 2
Hi ifatfat,


some few comments:

- indeed the opamp amplifies the difference, but the gain is made so high...that, in open loop, this statement doesnt translate into useful/measurable info(your output usually stick to the supply). The Opamp is considered most of the time in closed loop configuration (as it is the case here with the non-inverting configuration).

-Therefore in closed loop ONLY, try to find the right common mode voltage by puting a small AC signal (few millivolts) over a DC voltage -as an input to your non-inverting buffer- that you shall vary starting from vdd/2 until you see a convenient output.

- an opamp to the contrary to operational transconductance amplifier (OTA) have an output buffer to drive small load. How small ? this is what you should investigate. try with 1 kOhm first. to be in the safe side, then bit by bit decrease the resistance and augment the amplitude of your AC signal to see how much you can get of your opamp.

Also pay attention to the unity gain bandwith that will tell you the maximum frequency that your overall buffer can sustain.

-finally look carefully into the datasheet to check what type of load your opamp can accomodate: for instance the output capacitor may not be suitable for opamp stability reasons.








Posted  11/12/2012
A Disruptive Web Presence

Custom Search
Over 10,000 pages indexed! (none duped or pirated)

Read About RF Cafe
Webmaster: Kirt Blattenberger
    KB3UON

RF Cafe Software

RF Cascade Workbook
RF Cascade Workbook is a very extensive system cascaded component Excel workbook that includes the standard Gain, NF, IP2, IP3, Psat calculations, input & output VSWR, noise BW, min/max tolerance, DC power cauculations, graphing of all RF parameters, and has a graphical block diagram tool. An extensive User's Guide is also included. - Only $35.
RF system analysis including
frequency conversion & filters

RF & EE Symbols Word
RF Stencils for Visio

Product & Service Directory
Personally Selected Manufacturers
RF Cafe T-Shirts & Mugs

RF Cafe Software

Calculator Workbook
RF Workbench
Smith Chart™ for Visio
Smith Chart™ for Excel
Your RF Cafe Progenitor & Webmaster
Click here to read about RF CafeKirt Blattenberger... single-handedly redefining what an
                                 engineering website should be.

View the YouTube RF Cafe Intro Video Carpe Diem! (Seize the Day!)

5CCG (5th MOB): My USAF radar shop

Airplanes and Rockets: My personal hobby website

Equine Kingdom: My daughter Sally's horse riding website